Catalogue

Parts

Adriatic Machine Tools helps workshops brief parts, service visits, and rebuild paths in plain terms. We keep the catalogue practical for Gauteng floors.

Spindle Kit

Spindle kits are selected around taper type, drawbar condition and the heat the machine sees during long cutting cycles. On Gauteng sites, fine dust and missed lubrication checks often show up first as noise, run-out or poor surface finish. We note fitment points such as bearings, seals and retention parts so the replacement matches the spindle assembly in use.

Bearing Pack

A bearing pack needs the correct class, preload arrangement and grease specification for the spindle or axis it serves. Incorrect fitting pressure can mark races before the machine runs, so inspection matters as much as the part number. For workshops around Randburg, we also consider storage conditions, because boxed bearings left near moisture or grit can be compromised before installation.

Way Cover

Way covers protect slideways and screws from swarf, coolant splash and the abrasive dust that builds up in busy machining areas. Torn folds or bent slats usually start with chip overload, misalignment or a mounting edge pulling loose. We keep the focus on travel length, fixing points and cover style so the machine can move through its full stroke without binding.

Coolant Pump

Coolant pumps are matched by flow, head pressure, voltage and sump arrangement rather than by appearance alone. A weak pump often shows up as poor chip clearing, rising tool temperature or inconsistent delivery at the nozzle. In shops cutting cast iron or aluminium, sludge and fines can shorten pump life if the tank is not cleaned at the same time.

Tool Holder

Tool holders affect concentricity, clamping security and finish quality on every machining cycle. Collet condition, taper cleanliness and pull-stud compatibility all matter when chatter or tool pull-out becomes a problem. We list holders with the machine interface in mind, including common workshop checks for wear marks, fretting and damaged retention threads.

Axis Encoder

Axis encoders are tied to position feedback, repeatability and alarm tracing on CNC equipment. A failed unit may present as drift, reference return errors or unstable movement on one axis only. Cable routing, contamination at connectors and the exact encoder type are checked carefully before replacement is specified.

Ballscrew Set

Ballscrew sets are chosen around lead, end machining, support bearings and the load the axis carries in daily production. Backlash, uneven finish and servo strain can all point to screw wear or damage to the nut assembly. On machines exposed to dirt and poor lubrication, the thread surface often tells the story before a full failure occurs.

Servo Cable

Servo cables need the right plug layout, shielding and bend rating for the drive and motor pair on the machine. Cracked insulation, oil ingress and broken cores near the drag chain are common faults after years of travel. We pay attention to cable length, connector style and routing points so replacement does not introduce signal noise or intermittent trips.

Fixture Plate

Fixture plates support repeatable clamping, datum control and quicker changeovers on milling and drilling work. Material grade, flatness and hole pattern matter more than a plate that merely fits the table. Where corrosion or heavy hammering has marked older plates, a fresh setup surface can remove a hidden source of inaccuracy.

Oil Skimmer

Oil skimmers remove tramp oil from coolant sumps before smell, smoke and bacterial growth become harder to manage. Belt type, disc type and mounting position depend on tank access and how the machine collects surface oil. In warmer workshops, routine skimming can help coolant last longer and keep operators from dealing with a contaminated sump.

Filter Cart

Filter carts are used when coolant needs cleaning without emptying the whole tank or stopping a larger maintenance plan. They help remove fines, swarf and suspended debris that shorten pump life and affect cut quality. The useful details are media type, flow capacity and whether the cart suits neat oil, soluble coolant or a mixed-service workshop.

Training Kit

A training kit for machine-tool parts works best when it mirrors the components staff handle during servicing, change-outs and fault finding. Typical contents cover identification points, wear indicators and basic checks for fitment before a machine is powered again. This suits handover sessions where technicians or operators need a clear reference at the machine, not generic classroom material.

Coastal Pack

Coastal Pack deals with the salt-air, storage, and corrosion issues that often appear once the first parts cycle is done.

Highveld Pack

Highveld Pack deals with dust, dry conditions, and wear points that usually show up after the floor settles into routine.

Night Shift

Night Shift deals with the breakdowns, handover gaps, and missing spares that tend to surface after daytime support leaves.

Export Week

Export Week deals with crating, paperwork, and machine-part checks that become critical once freight planning starts.

Training Day

Training Day deals with setup mistakes, handling wear, and operator questions that come through once the machine is in use.

Spares Bridge

Spares Bridge covers the hard-to-find machine-tool parts that usually stop a workshop after the first steady run.